• Jotun Solvalitt - Aluminium

Jotun Solvalitt Heat Resistant Paint - Aluminium Finish - 5 Litre

Product Ref: IPS103A

2 people have viewed this product in the last 24 hours

Options
5 Litre
£0.00 ex. VAT £0.00 inc. VATRRP: £0.00
View Favourites

 In stock 

Out of stock

Product Rating

No rating yet

Write your own review

Write a review

Thank you. Your review has been submitted and subject to moderation, will appear on this page shortly.

0 loyalty points

Ask a Question

We reply in 59 minutes or less within business hours.

Thank you for your interest in Ultrimax Coatings Ltd.

There was a problem with the form submission, please try again.

Product Description

 

Jotun Solvalitt - High Temperature Paint

This is a one component physically drying silicone acrylic coating. It is an aluminium pigmented product.

Jotun Solvalitt Aluminium is a one component physically drying silicone acrylic coating that is an aluminium pigmented product leaving a metallic silver finish. Suitable for properly prepared carbon steel, galvanised steel, stainless steel and aluminium substrates.

 

1K Heat Resistant Paint by Jotun

Jotun Solvalitt Alu is designed as a heat resistant coating suitable for insulated and non insulated surfaces.

Dry, atmospheric - Heat resistance = 600 °C

Peak temperature duration max. 1 hour.
The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.

 

Recommended Use for Heat Resistant Paint

Protective:

Designed as heat resistant coating. Suitable for insulated and non insulated surfaces. Recommended in combination with an inorganic zinc silicate coating as primer, providing heat resistance up to 400 °C and long corrosion protection.

For shorter periods, such a combined system can handle peak temperatures up to 540 °C.

 

Colours

Aluminium finish.

 

Technical Detail

  • Solids - 40%
  • VOC - 500gms/litre
  • Spreading rate - 19sqm/ltr
  • Gloss - Matt
  • Thinners - No.7
  • Primer - Resist 78
PropertyTest/StandardDescription
Solids by volumeISO 323343 ± 2 %
Gloss level (GU 60 °)ISO 2813matt (0-35)
Flash pointISO 3679 Method 126°C
Densitycalculated1.3 kg/l
VOC-EUIED (2010/75/EU) (theoretical)483 g/l

 

The provided data is typical for factory produced products, subject to slight variation depending on colour.

Note: Heat resistant topcoats can be tinted in a range of colours. However, due to its pigmentation certain colours will appear less gloss and colour stable than others.


 

Film Thickness per Coat


Typical recommended specification range
Dry film thickness20-30μm
Wet film thickness50-70μm
Theoretical spreading rate21-14m²/l


 

Surface Preparation


To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination.

 

Surface preparation summary table
SubstrateMinimumRecommended
Carbon steelSa 2½ (ISO 8501-1)Sa 2½ (ISO 8501-1)
Stainless steelCleanliness and surface profile corresponding to Sa 2½ (ISO 8501-1), Fine G (ISO 8503-2)Cleanliness and surface profile corresponding to Sa 2½ (ISO 8501-1), Fine G (ISO 8503-2)
The surface shall be hand or machine abraded with non-metallic abrasives or bonded fibre machine or hand abrasive pads to impa

Compare Products (0)

This site uses cookies to provide you with a better on-site experience. By continuing your visit, you accept their use as set out in our Cookie & Privacy Policy. OK

Chat