Time Remaining
Jotun Paint Resist 78 - 2 Pack Zinc Primer - 11.6 Litre
Product Ref: IPR7820
3 people have viewed this product in the last 24 hours
In stock
Product Rating
No rating yet
Write a review
Thank you. Your review has been submitted and subject to moderation, will appear on this page shortly.
0 loyalty points
Ask a Question
We reply in 59 minutes or less within business hours.
Thank you for your interest in Ultrimax Coatings Ltd.
There was a problem with the form submission, please try again.
Product Description
Jotun Paint Resist 78 - 2 Pack Zinc Primer
A two pack , quick curing, zinc rich ethyl silicate based coating. Resistant to cyclic dry temperatures up to 400C.
Jotun Resist 78 is a two component moisture cured inorganic zinc ethyl silicate coating that is a fast curing, very high zinc dust containing product.
It conforms to the compositional requirements of SSPC paint 20, level 2 and ISO 12944-4. It provides excellent corrosion protection as part of a complete coating system and is often used as a zinc primer before topcoat.
It is heat resistant up to 540°C. To be used as a primer in atmospheric environments for properly prepared carbon steel substrates only. This product complies with ASTM D520 type I zinc dust.
Jotun Resist 78 is suitable for structural steel and piping to be exposed to corrosive environments up to very high.
Recommended for offshore environments, refineries, power plants, bridges, buildings and mining equipment. Specially designed as a primer in coating systems where extended durabilty is required.
Features & Benefits
- Designed for protection in severe corrosive environments
- Fast dry to recoat and fast to handle
- All year around Certified in systems for Norsok system 1
- Two component moisture cured inorganic zinc rich ethyl silicate coating
- High zinc dust content
- Conforms to the compositional requirements of SSPC paint 20, level 2 and ISO 12944/ISO 20340
- Heat resistant up to 400 degrees Celsius
- Easy application
- Fast dry to recoat and fast to handle
- “Green step” – Health, Environment and Safety
- Pure zinc dust (ASTM D520 type II)
2 Pack Zinc Primer Paint by Jotun
Recommended for offshore environments, refineries, power plants, bridges, buildings and mining equipment. Specially designed as a zinc primer in coating systems where extended durabilty is required.
Recommended Primer for Durability
Typical use:
Designed for protection in severe corrosive environments
Protective:
Suitable for a wide range of industrial structures.
- Fast dry to recoat and fast to handle
- All year around Certified in systems for Norsok system 1
Approvals and certificates
- Pre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 1, suitable for exterior exposure in offshore environment, below 120°C.
- Tested by independent institute for static coefficient of friction
Colours
Grey
Other Penguard Paints:
Other variants available
Pilot 2
Penguard Topcoat
Penguard Express MIO
Penguard Express ZP
Penguard Express CF
Suitable for structural steel and piping to be exposed to highly corrosive environments, C5I or C5M (ISO
12944-2). Recommended for offshore environments, refineries, power plants, bridges, buildings and mining
equipment.
Refer to separate TDS for each variant
Jotun Paint - Zinc Primer
Application methods
The product can be applied by
Spray: Use airspray or airless spray.
Brush: Recommended for stripe coating and small areas. Care must be taken to achieve the specified dry film thickness. In order to avoid settling
Technical Detail
Manufacturer - Jotun
Water / Solvent Based - Solvent
For Use On - Steel
Application Method - Airless Spray, Spray, Brush
Sheen - Matt
Colour - Standard / Ready Mixed
Single, Two or Three Pack - Two-Pack
Product Certifications - NORSOK M-501, Rev. 5, System 1
Coverage - 8 to 14.4m² per litre
Touch Dry - 15 mins
UN Number (Activator) - UN1263
UN Number (Base) - UN3077
Downloads
Videos
Other Customers Also Bought:
The below products are often purchased together with the above item.
