• Jotun Penguard Clear Varnish
  • IPTC05 4
  • IPTC05 2
  • IPTC05 3

Jotun Paints Penguard Clear Varnish - Concrete Sealer

Product Ref: IPTC05

3 people have viewed this product in the last 24 hours

5 Litre
£70.30 ex. VAT £84.36 inc. VATRRP: £0.00
View Favourites

In stock2-3 Days

Product Rating

No rating yet

Write your own review

Write a review

Thank you. Your review has been submitted and subject to moderation, will appear on this page shortly.

0 loyalty points

Ask a Question

We reply in 59 minutes or less within business hours.

Thank you for your interest in Ultrimax Coatings Ltd.

There was a problem with the form submission, please try again.

  • The CAPTCHA could not be validated. Please try again.

Product Description

 

Jotun Penguard Clear Varnish - Concrete Sealer

This is a two component transparent polyamide cured high molecular weight epoxy concrete sealer coating. It has excellent penetrating properties and is designed as a sealer coat for concrete surfaces. Can be used as primer or finish topcoat in a complete system in atmospheric environments.

 

Price Promise On Jotun Paints 2 Pack

Our Price Promise : Our Jotun Paints 2 Pack Products Pricing includes BOTH Paint and Hardener as a package. Does your competitor offer the same?

 

Jotun Penguard Clear Varnish Colours

Concrete sealer colour: transparent

Typical use: protective concrete sealer, Penguard Primer paint or Penguard Topcoat

Protective: Suitable for concrete sealing when exposed to a wide range of environments.

 

Jotun Penguard Clear Varnish Surface Preparation

To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.

Technical Detail

Jotun Penguard Concrete Sealer Spreading Rates

Film thickness and spreading rateDry Film Thickness(μm)Wet film thickness(μm)Theoretical Spreading rate(m²/l)
Minimum307014,7
Maximum501158,8
Typical409011

 

Jotun Penguard Advised Concrete Sealer Application

Concrete Sealer Application methods
The product can be applied by

Clear Varnish Spray: Use airless spray.
Clear Varnish Brush: Recommended.
Clear Varnish Roller: Recommended.

 

Jotun Penguard Product mixing ratio (by volume)

Penguard Clear Sealer Comp A - 4 part(s)
Penguard Comp B - 1 part(s)

 

Recommended Thinners/Cleaning solvent

Thinner: Jotun Thinner No. 17

Thinner: Ultrimax

 

 

Guiding data for airless spray

Nozzle tip (inch/1000): 15-23
Pressure at nozzle (minimum): 150 bar/2100 psi

 

Penguard Clear Varnish Concrete Sealer Drying Times

Drying and curing times are determined under controlled temperatures and relative humidity below 85%, and within the DFT range of the product.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,imprints or other physical damage.

Dried to over coat, minimum: The shortest time allowed before the next coat can be applied.

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal tackiness. Dry sand sprinkled on the surface can be brushed off without sticking to or causing damage to the surface.

Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended environment/medium.

Compare Products (0)

This site uses cookies to provide you with a better on-site experience. By continuing your visit, you accept their use as set out in our Cookie & Privacy Policy. OK

Chat